Attach Rear License Plate Without Screws: 3 Expert Guidelines for Beginners

Can you attach rear license plate without screws? Yes, you can attach a rear license plate without screws. The best way to attach a rear license plate without screws is to use the magnetic number plate holder.

In many states, drivers are required to display a license plate on the rear of their vehicle. Often, these plates are attached with screws. However, a few ways to attach a license plate without screws exist.

In this article, we promise to share several methods about how to put a license plate on a car without screws. We’ll also share the guidelines for properly installing license plates without screws in the car.

Attach Rear License Plate Without Screws- 3 Ways

We promised earlier that we’d discuss step by step how to install license plate fasteners. There are three easy methods we will reveal, and you must benefit by following any of these you like.

Method 1: Magnetic Number Plate Holder

Installing a magnetic number plate holder is easy to keep your license plate in place. The holder attaches to the top of your car with magnets, so it’s easy to install and remove. Plus, it doesn’t damage your car or license plate.

To install the holder, first clean the area where you will attach it using rubbing alcohol or a glass cleaner. Wipe down the surface until it is free of dirt or dust particles. 

Next, peel off the magnetic adhesive backing and attach it to the top of your car. Ensure both magnets are attached securely before moving on to the next step.

Now take the license plate frame and fit it around your license plate as you would normally do when installing a frame onto a license plate.

Once everything is in place, hold up the number plate holder against the frame and use either one or two hands (depending on how big your hands are) to snap each corner into place. 

If everything has been installed correctly, there should be no gaps between the number plate holder and frame. You may need to adjust the position of either component depending on where your license plate sits on your car.

Method 2: Double-Sided Tape

This method is relatively simple and can be done in a few minutes. Installing a license plate with double-sided tape is a quick and easy process. There are 3 types of double-sided tape available in the market. You can go with anyone.

First, clean the area where you will apply the tape with rubbing alcohol or another cleaning agent. Next, peel the backing off one side of the tape and press it firmly against the license plate. 

Next, peel off the other side of the backing and press it against your car’s body. Hold it in place for a few seconds to ensure it sticks securely.

Note: If you’re using double-sided tape to install your rear license plate, choose a tape designed for automotive use. This type of tape is weather-resistant and won’t lose its stickiness over time.

Method: 3 Using Velcro

If you want to install a license plate with velcro, you will need to purchase some velcro strips. You can find these at most hardware stores. 

Once you have your velcro strips, you will need to clean the area where you will be attaching the strips. It can be done with mild soap and water. Once the area is clean, you must dry it completely before attaching the velcro. 

To attach the velcro, you will need to peel the backing off of one strip and attach it to the top corner of the license plate. 

Then, you will need to take the other strip of velcro and attach it to the bottom corner of the license plate. Once both strips are attached, you will need to press the strips together to secure the license plate.

Benefits of Installing a License Plate Without Screws

Using a license plate without screws or a drill has many benefits. One of the major benefits is that it prevents damage to your car. But when you use a license plate with a drill, you can easily damage your car’s paint job or bumper. 

Another benefit is that it’s easy to install and remove. You don’t need tools or drilling skills to put it on or take it off. Finally, using a license plate without a drill is more affordable than other options available on the market.

This Video Will Help You Too!

Frequently Asked Questions (FAQs)

Can you use self-tapping screws for the license plate?

These self-tapping screws have a special design that allows them to tap into the surface of the license plate holder without needing any pre-drilling. It makes them quick and easy to use and helps ensure a secure attachment.
If you’re looking for a quick and easy way to attach your license plate securely, then self-tapping screws may be right!

How do you attach a front plate without holes?

There are three methods we have mentioned above. You can attach a front license plate without drilling holes. 
These methods are magnetic number plates, heavy-duty double-sided 3M tape, and the use of Velcro. Using these methods, you can attach a front license plate properly without any damage.

How do you install a magnetic license plate holder?

There are a few simple steps to install your magnetic license plate holder. The steps are quick and easy to follow.
First, clean the surface of your car where the holder will be installed. It will ensure that the adhesive tape will stick properly. Next, peel off the backing from the adhesive tape and attach the holder to your car. Finally, press the license plate into the holder, and you’re all set!

How do you install a plastic license plate fastener?

Installing a plastic license plate fastener is an easy process that can be completed in just a few minutes. The first step is to remove the old license plate screws from your car. 
Next, use the included screws and washers to attach the new license plate fastener to your car. Finally, reattach your license plate using the new screws and washers.

How do you put a license plate clip on?

There are a few ways to put a license plate clip on, but the most common way is to use two screws. First, find the two holes on the back of the license plate. These will be where the screws will go. 
Next, take the license plate clip and line it up with the holes. Once it is lined up, put the screws in and tighten them. That’s it! Your license plate clip is now on.

Conclusion

So far, we have mentioned several methods to attach rear license plate without screws or a drill. We have also described the proper guidelines for each method of installing a registration plate on the car.

Moreover, we have depicted the advantages of using a license plate without screws, and you will get benefited if you use it. Following each method is quick and easy and can be done in a few minutes. You do not need the help of any tools. You can do it own yourself. 

But whichever way you choose, ensure the license plate is securely attached, so it does not fall off while driving.

You Can Also Read:

Similar Posts